U_Soldier
Power Member
OLa estou a tentar ter o meu cpu estavel a 3600 24/7 a board é uma Rampage Formula com os setings abaixo fez 9h de prime mas estou com problemas de cold boot , tipo chego a casa do trabalho ligo a maquina bam ecran azul no loading do windows faz reset e reenicia perfeitamente sem problemas.
Alguem sabe de algo que eu esteja a falhar.
Aqui ficam os meus setings
Extreme Tweaker menu:
CPU Level Up [Auto] Auto
Ai Overclock Tuner [Auto] Manual
OC From CPU Level Up [Auto] Auto
CPU Ratio Setting [Auto] Auto
FSB Strap to North Bridge [Auto] 333
FSB Frequency [XXX] 450
PCIE Frequency [XXX] 100
DRAM Frequency [Auto] Auto
DRAM Command Rate [Auto] Auto
DRAM CLK Skew on Channel A/B [Auto] Auto
DRAM Timing Control [Auto] Auto
1st Information : 4-5-5-15-3-42-6-3 (These values are auto-detected) CPU-Z says 5:6 1080MHz
CAS# Latency [5 DRAM Clocks] 5
RAS# to CAS# Delay [5 DRAM Clocks] 5
RAS# PRE Time [5 DRAM Clocks] 5
RAS# ACT Time [15 DRAM Clocks] 18
RAS# to RAS# Delay [Auto] Auto
REF Cycle Time [Auto] Auto
WRITE Recovery Time [Auto] Auto
READ to PRE Time [Auto] Auto
2nd Information : 8-3-5-4-6-4-6(These values are auto-detected)
READ to WRITE Delay (S/D) [Auto] Auto
WRITE to READ Delay (S) [Auto] Auto
WRITE to READ Delay (D) [Auto] Auto
READ to READ Delay (S) [Auto] Auto
READ to READ Delay (D) [Auto] Auto
WRITE to WRITE Delay (S) [Auto] Auto
WRITE to WRITE Delay (D) [Auto] Auto
3rd Information : 13-5-1-5-5 (These values are auto-detected)
WRITE to PRE Delay [Auto] Auto
READ to PRE Delay [Auto] Auto
PRE to PRE Delay [Auto] Auto
ALL PRE to ACT Delay [Auto] Auto
ALL PRE to REF Delay [Auto] Auto
DRAM Static Read Control [Auto] Auto
Ai Clock Twister [Auto] Auto
Ai Transaction Booster [Auto] Auto
Pull-In of CHA PH1
Pull-In of CHA PH2
Pull-In of CHB PH1
Pull-In of CHB PH2
CPU Voltage [Auto] (Vcc) 1.34000
CPU PLL Voltage [Auto] 1.54
North Bridge Voltage [Auto] (NBCore) 1.51
DRAM Voltage [Auto] 2.1
FSB Termination Voltage [Auto] (VTT) 1.34
South Bridge Voltage [Auto] (SBCore) Auto
SB 1.5V Voltage [Auto] Auto
Loadline Calibration [Auto] Auto
CPU GTL Voltage Reference [Auto] Auto
NB GTL Voltage Refernece [Auto] Auto
DRAM Controller Voltage REF [Auto] Auto
DRAM Channel A Voltage REF [Auto] Auto
DDR2 Channel B Voltage REF [Auto] Auto
CPU Spread Spectrum [Auto] Auto
PCIE Spread Spectrum [Auto] Auto
Advance Menu/CPU Configuration:
CPU Ratio Setting [Auto] Auto
C1E Support [Disabled] Disabled
CPU TM Function [Enabled] Enabled
Vanderpool Technology [Enabled] Disabled
Max CPU ID Value Limit [Disabled] Disabled
Intel Speedstep Tech. [Enabled] Disabled
Advanced Menu/North Bridge Chip:
Memory remap (for 64bit OS's) [Enabled] Enabled
Alguem sabe de algo que eu esteja a falhar.
Aqui ficam os meus setings
Extreme Tweaker menu:
CPU Level Up [Auto] Auto
Ai Overclock Tuner [Auto] Manual
OC From CPU Level Up [Auto] Auto
CPU Ratio Setting [Auto] Auto
FSB Strap to North Bridge [Auto] 333
FSB Frequency [XXX] 450
PCIE Frequency [XXX] 100
DRAM Frequency [Auto] Auto
DRAM Command Rate [Auto] Auto
DRAM CLK Skew on Channel A/B [Auto] Auto
DRAM Timing Control [Auto] Auto
1st Information : 4-5-5-15-3-42-6-3 (These values are auto-detected) CPU-Z says 5:6 1080MHz
CAS# Latency [5 DRAM Clocks] 5
RAS# to CAS# Delay [5 DRAM Clocks] 5
RAS# PRE Time [5 DRAM Clocks] 5
RAS# ACT Time [15 DRAM Clocks] 18
RAS# to RAS# Delay [Auto] Auto
REF Cycle Time [Auto] Auto
WRITE Recovery Time [Auto] Auto
READ to PRE Time [Auto] Auto
2nd Information : 8-3-5-4-6-4-6(These values are auto-detected)
READ to WRITE Delay (S/D) [Auto] Auto
WRITE to READ Delay (S) [Auto] Auto
WRITE to READ Delay (D) [Auto] Auto
READ to READ Delay (S) [Auto] Auto
READ to READ Delay (D) [Auto] Auto
WRITE to WRITE Delay (S) [Auto] Auto
WRITE to WRITE Delay (D) [Auto] Auto
3rd Information : 13-5-1-5-5 (These values are auto-detected)
WRITE to PRE Delay [Auto] Auto
READ to PRE Delay [Auto] Auto
PRE to PRE Delay [Auto] Auto
ALL PRE to ACT Delay [Auto] Auto
ALL PRE to REF Delay [Auto] Auto
DRAM Static Read Control [Auto] Auto
Ai Clock Twister [Auto] Auto
Ai Transaction Booster [Auto] Auto
Pull-In of CHA PH1
Pull-In of CHA PH2
Pull-In of CHB PH1
Pull-In of CHB PH2
CPU Voltage [Auto] (Vcc) 1.34000
CPU PLL Voltage [Auto] 1.54
North Bridge Voltage [Auto] (NBCore) 1.51
DRAM Voltage [Auto] 2.1
FSB Termination Voltage [Auto] (VTT) 1.34
South Bridge Voltage [Auto] (SBCore) Auto
SB 1.5V Voltage [Auto] Auto
Loadline Calibration [Auto] Auto
CPU GTL Voltage Reference [Auto] Auto
NB GTL Voltage Refernece [Auto] Auto
DRAM Controller Voltage REF [Auto] Auto
DRAM Channel A Voltage REF [Auto] Auto
DDR2 Channel B Voltage REF [Auto] Auto
CPU Spread Spectrum [Auto] Auto
PCIE Spread Spectrum [Auto] Auto
Advance Menu/CPU Configuration:
CPU Ratio Setting [Auto] Auto
C1E Support [Disabled] Disabled
CPU TM Function [Enabled] Enabled
Vanderpool Technology [Enabled] Disabled
Max CPU ID Value Limit [Disabled] Disabled
Intel Speedstep Tech. [Enabled] Disabled
Advanced Menu/North Bridge Chip:
Memory remap (for 64bit OS's) [Enabled] Enabled
Última edição: