1. Este site usa cookies. Ao continuar a usar este site está a concordar com o nosso uso de cookies. Saber Mais.

rEFIt - triple boot - Vista setup encontra partição onde instalar

Discussão em 'Dúvidas e Suporte Técnico - Apple' iniciada por The_Prophet, 25 de Maio de 2008. (Respostas: 1; Visualizações: 2913)

  1. enho estado a tentar instalar o Mac-OS + openSuse + Vista num Macbook pro, mas o quando chego a instalação final do vista o setup não encontra uma partição onde possa instalar.

    sda
    1- rEFIt Partition
    2- Mac OS
    3- Suse
    4- Vista


    Tenho estado a seguir = Ivan N. Zlatev BLoG
    http://i-nz.net/2007/05/14/apple-mac-triple-boot-howto/

    E chego ao ultimo ponto (5), mas o Vista o setup nao encontra uma partição onde possa instalar.

    Alguém me pode ajudar ?

    thkx
    -----------------""-------------""-------------


    I - folowed Ivan N. Zlatev BLoG
    http://i-nz.net/2007/05/14/apple-mac-triple-boot-howto/

    1 - Partitioning

    Boot from your Mac OS X CD 1 and use Disk Utility from the menu on top to
    create one partition for Mac OS X, one Unix type partition and one FAT32
    type partition. It appears that it is crucial to have the Windows partition
    as the last one, else Vista will complain and won’t even install and
    Windows XP will install, but will throw missing hal.dll error and won’t
    boot.

    2 - Install Mac OS X

    Install Mac OS X and update it to the latest version. Reboot and install
    rEFIt. Reboot and use the sync tool (called “Partition Tool” in the
    menu) in the rEFIt menu to sync MBR to GPT.

    3 - Install Windows Vista (setup NTFS partition)

    In Vista’s setup select the FAT32 partition, format it and install there.
    After the first reboot during the installation use rEFIt sync tool again.
    This is just to get the NTFS partition in place. Do not finish off the
    installation now, but rather procceed to the Linux installation. Windows
    won’t be able to boot after the sync anyway.

    4 - Install Linux (openSUSE)

    Crucial elements during the installation of openSUSE before the first
    reboot:

    * Install Linux (yes, everything) on the single UNIX type partition.
    Use custom partitioning to format the UNIX type partition to ext3 and set
    mount point to /. Do not create a swap partition and do not even think
    about resizing partitions.
    * Set the boot loader to LILO, because GRUB will fail to install.
    * Install the boot loader in the boot record for the partition. REFIt
    can boot it fine and also the master boot record will be free for Windows
    later on.
    * Remove the Windows entry from the lilo menu, because it causes
    LILO’s installation to fail.

    Unfortunatly for unknown reasons to me after the first reboot during the
    installation the MBR partitioning table will be gone, so one has to use
    rEFIt to resync GPT and MBR. This of course will break lilo’s previous
    setup, so we have to reinstall it before continuing the installation. This
    can be done by boot from the openSUSE cd/dvd again and once the setup has
    loaded Ctrl + Fx to a terminal. From that point on we have to mount the
    partition where we have Linux installed and rerun lilo:

    mkdir /media/suse;
    mount /dev/sda3 /media/suse
    mount --bind /dev /media/suse/dev
    chroot /media/suse
    lilo -v

    Reboot and resync GPT/MBR once more (so that rEFIT sets proper partition
    types) and then reboot for the last time. You should see OS X, Windows
    (won’t boot) and Linux icons in the rEFIt menu now. Select the Linux one
    and finish your openSUSE installation.

    5 - Install Windows Vista

    Run the Windows Vista installation from the start (again by formatting the
    partition) to end now. Do not sync MBR/GPT after!
     
  2. Ta resolvido era so activar com o fdisk a partição correcta .. ..

    se alguem tiver este prob é so ir a prompt do mac-os /fdisk / print --> para ver a lista de part


    e executar = flag com o nº da partição [a ultima]
     

Partilhar esta Página